Electric BMW M3 – the technology under the skin.

Four motors, no differential and a control loop running every millisecond: with the electric M3 (ZA0), BMW M has developed almost everything from scratch. After the first drive impressions, we take a closer look at the technology behind the new M3 – from the powertrain and battery to the chassis. All figures are preliminary BMW data.
Two drive units, four motors
At the heart of it all is M eDrive, based on the Neue Klasse's Gen6 technology. Each axle carries a so-called Sport Drive Unit. Inside each unit, two electric motors sit side by side in parallel, rotated 180 degrees to each other. Every motor drives exactly one wheel through its own single-speed gearbox.
Importantly, these are not hub motors. The motors sit inside the car, keeping unsprung mass low. A 3-level inverter is mounted on top of each unit, controlling the motors more precisely and with lower losses than a conventional design.
Front axle: around 480 kW and 540 Nm
Rear axle: around 560 kW and 1,000 Nm
System: 625 kW (850 PS) and around 1,200 Nm
The axle figures cannot simply be added together. The setup is clearly rear-biased: the rear axle receives almost twice as much torque as the front.
No more differential
There is no mechanical differential. Because every wheel has its own motor, the software distributes torque directly. Torque vectoring works through the motors alone – without brake intervention or multi-plate clutches. The higher the lateral acceleration, the more torque goes to the outside wheels.
The front axle can be fully disconnected via a decoupling unit. In Comfort mode, the M3 mostly runs as a pure rear-wheel-drive car to save energy, for example on the motorway. In Sport and Sport Plus, all-wheel drive stays permanently engaged.
BMW evaluated several concepts: rear- and all-wheel drive with two, three or four motors. It chose four because they offer the best control. Failure was considered too: if one motor fails, the system shuts down the affected axle and keeps driving on the other.
Heart of Joy: control every millisecond
The Neue Klasse uses four high-performance computers, known as Superbrains. One of them, the "Heart of Joy", is responsible for driving dynamics. In the M3, it runs BMW M's own software, M Dynamic Performance Control.
The difference to the past is huge. Previously, separate control units for powertrain and chassis communicated in cycles of 10 to 20 milliseconds. Now a central unit calculates every millisecond. Each motor can also change its torque within roughly one millisecond.
This shows in the ABS as well. The friction brakes supply the base braking force, while the motors handle the rapid modulation. They react faster than any hydraulic system.
Braking and regeneration
When slowing down, regeneration takes priority. The M3 recovers up to 540 kW – more than any other Gen6 model. Lifting off the throttle alone decelerates the car at up to around 0.4 g. The discs only step in when more braking force is needed, depending on state of charge and speed.
Customers can choose between M Compound and M Carbon ceramic brakes. According to BMW, the system is smaller than expected and even slightly lighter than on the current M3. After several fast laps, the carbon-ceramic discs measured only 55 to just over 70 °C, depending on the report.
A battery with M cells
The sixth-generation pack holds around 100 kWh. The cylindrical cells share the format of the i3's cells but differ inside. Larger, thinner electrodes and more electrolyte enable higher power output. According to BMW, the cell chemistry is the same, though it has not been named.
Cooling is considerably more elaborate. In the i3, every second row of cells is cooled; in the M3, every row is, so each cell is cooled on both sides. Larger water pumps and an M-specific control unit called Energy Master complete the package.
Electrical architecture: 800 volts
DC charging: up to 420 kW
Charging: up to around 350 km in 10 minutes (test cycle unconfirmed)
Range: around 650 km WLTP
The battery housing has the same dimensions as the i3's. In the M3, however, it is bolted to both axle carriers via corner mounts and acts as a shear panel. The battery thus becomes a load-bearing part of the body.
Built for the track
Electric cars often lose power on track after just a few laps. BMW M aims to prevent this with a dedicated Track program. Selecting it starts preconditioning of the battery and drivetrain. Drivers then choose the length of the session:
Hot Lap: up to 2 minutes
Short Run: up to 8 minutes
Long Run: up to 15 minutes, with at least 80% state of charge
The system sets power and torque limits for the chosen duration so that output stays consistent to the end. During testing at Miramas, the state of charge dropped from 100 to around 60 percent over ten laps. Regeneration recovers about a third of the energy on track, and up to half on a briskly driven mountain road.
Six stages and M eSound
M eDrive divides the speed range into six stages. Each stage has its own agility value, shown in the head-up display. There are three modes: Auto S as the default, Manual S with paddles, shift lights and a limiter, and D for classic single-stage EV driving.
Full power is available at the top of each stage, and the sprint to 100 km/h is just as quick with or without the stages. Regeneration also depends on the stage: the lower stages brake harder. The synthetic M eSound becomes more aggressive as agility rises. Inside, it can be set to Mid, Max or Off; outside, it is always active for legal reasons.
Chassis: all new
In the M3, battery, chassis and body form a single structural unit. Stiffening plates made of 8 mm aluminium connect both axle carriers. At the front, forged aluminium parts and braces from the shock towers to the A-pillars add rigidity. At the rear, five forged aluminium links per side locate each wheel.
The dampers are completely new and not taken from the i3's adaptive M suspension. The springs are progressive and stiffer. The steering uses an M-specific ratio, and software filters out disturbances from the drivetrain. The front axle was designed so that hardly any drivetrain influence can be felt through the steering.
The prototypes ran on Michelin Pilot Sport S 6 tyres, 275/35 R20 at the front and 295/35 R20 at the rear. For comparison, today's M3 Competition uses 19- and 20-inch wheels.
Natural fibre instead of carbon
The familiar M Carbon bucket seats are replaced. The new seats have a natural-fibre composite structure, an illuminated M3 badge and a patented cushion adjustment. The material offers properties similar to carbon fibre but cuts CO2 emissions in production by around 40 percent. BMW M has been using it in motorsport since 2019, for example in the M4 GT4.
What remains open
BMW is still holding back some key data:
Weight (likely above the i3's 2,280 kg)
Acceleration and top speed
Motor type and cell chemistry
Charging time from 10 to 80 percent
Production plant, market launch and price
There are also differences regarding the battery size: in January, BMW spoke of more than 100 kWh of usable capacity, while at the test event the figure was "around 100 kWh".
The electric M3 is not a converted i3 but an M car developed in its own right. Four motors without a differential, central control every millisecond and a battery as a load-bearing component – technically, BMW M is raising the bar significantly. Whether the overall package convinces will become clear once the weight is known and the first road tests take place. The world premiere is planned for 2027, and the combustion M3 (G84) will be offered alongside it.
All technical details are based on preliminary BMW data and impressions from drives in pre-production prototypes. They will only be final once the car is officially unveiled.
Meine Blog Artikel erstelle ich aus folgenden Quellen und Hilfsmittel:
Quellen: BMW Press Group, Google, Instagram, Erfahrungen aus dem Auto Gewerbe
Hilfsmittel: Für die Grammatik der Texte nutze ich Google Gemini und Claude




Comments